醫療用內窺鏡設備定期保養一般由儀管員配合工程技術人員完成，它是一項不斷循環進行的有組織有計劃的維修措施，這有利于掌握儀器的運行規律，有利于出現故障后的查找。下面
內窺鏡設備維修人員來講講其保養事項。
The regular maintenance of medical endoscope equipment is generally completed by the instrument controller in cooperation with the engineering technicians. It is an organized and planned maintenance measure that is carried out in a continuous cycle, which is conducive to mastering the operation rules of the instrument and to finding out after the failure. The maintenance personnel of endoscope equipment will talk about its maintenance items.
⑴一保：一般可以一個月一個季度進行一次.主要內容除廠日常維護的工作外，可以拆開機殼，各處積塵，污垢、異物、緊固螺絲、添加潤滑劑；檢查務器件、元件有無磨損、變形、燒蝕、擊穿、松動，受潮，老化、接地不良等情況；檢測各組電源電壓及紋波，檢查高壓部件運行和接觸情況等；
(1) First maintenance: generally, it can be carried out once a month to once a quarter. In addition to the daily maintenance work of the factory, the main contents can be disassembled, dust, dirt, foreign matter, fastening screws, and lubricant can be removed everywhere; Check the service devices and components for wear, deformation, ablation, breakdown, looseness, moisture, aging, poor grounding, etc; Check the power supply voltage and ripple of each group, and check the operation and contact of high-voltage components;
⑵二保：一般可以半年一年進行一次。主要內容除做好一保外，可以對整機控制臺上的各個儀表及操作控制系統的靈敏度，精度進行測試校正和計量檢定，更換高壓發生器絕緣汕等到期的損耗品，對電路中各測試點的電壓，波形進行系統檢測和做拉偏試驗；
(2) Secondary insurance: generally, it can be carried out once every six months to one year. In addition to the first guarantee, the main contents include testing, calibration and metrological verification of the sensitivity and accuracy of each instrument and operation control system on the console of the whole machine, replacement of expired loss products such as high-voltage generator insulation, systematic detection of the voltage and waveform of each test point in the circuit, and pull bias test;
⑶三保：一般可以2-4年進行一次：主要內容除做好二保外，必要寸可以將整機進行全部拆卸子以清洗檢修，超過使用期的元器件應盡量更換或修復，應對儀器進行較為綜合的調試，恢復其工作精度和性能，達到或超過新機的程度是完全有可能的。
(3) Three guarantees: generally, it can be carried out once every 2-4 years. In addition to the second guarantee, the whole machine can be fully disassembled for cleaning and maintenance when necessary. Components beyond the service life should be replaced or repaired as much as possible. The instrument should be comprehensively debugged to restore its working accuracy and performance. It is completely possible to reach or exceed the level of the new machine.
The content and time of regular maintenance are different for different instruments. Generally, it can be divided into three levels. The above is the content of the relevant answers to the questions. I hope to give you good help. Please come to our website for more matters http://www.yojeim.com consulting service
新聞資訊
聯系我們
公司：匠仁醫療設備有限公司 
新聞資訊
